John Deere 635F HIDROFLEKS 10,7 m import iz SShA adapter za žito

A beautiful John Deere 635F platform made in 2008 (the actual year of manufacture).
Not painted, not boiled, not beaten.
The bottom is intact in paint, the top and bottom are all intact. The stainless steel sheet is in good condition.
New almost protective / sliding plates on the bottom, replaced last year.
Fingers on the auger are intact, mostly new.
Normal working segments and scythe pressure plates are fine.
High side (stone protection) on the scythe.
All levers and brackets are visually in good condition.
The tines are intact, not cut. Plastic half-bearings without wear.
The auger is good, without flaws, in good condition.
It seems to have been used relatively little and carefully.

The cost in Ukraine is 18 thousand US dollars.
I offer IMPORT from the USA on order (or in stock in the spring) John Deere 635F Gydra-Flex flex/hydro-flex platform 2005 - 2010 from the USA, working width 10.67 meters, hydro-flex.
The estimated time of arrival at the warehouse in Kyiv is spring 2024, which is actually two months before the harvest of early grain. The John Deere platform is best suited for harvesting primarily soybeans, as well as cereals.
This John Deere 635 Hydroflex platform differs from the 9 Series platforms in the hydraulic drive of the floating part of the platform, as well as the American "Jondery" so-called "Schumacher". Instead of the MCS, this platform uses a planetary mechanism, which is characterized by its reliability and durability.
General characteristics of this platform:
- John Deer brand;
- model 635F hydroflex, GYDRAFLEX;
- working width - 10.6 meters;
- year of manufacture: 2004-2010;
- automatic reel feeding;
- fingers all around the auger, Full-Finger auger;
- American "Schumacher", planetary mechanism.
A good header with a total operating time of no more than 4000 hours.

JOHN DEERE 635 F hydroflex header/platform 10.67 meters imported from the USA, without operating time in Ukraine, imported American flex platform.
The John Deere 635 flex platform is indispensable for harvesting low-growing legumes, such as soybeans, first of all. Thanks to these flex platform, losses during soybean mowing are minimized. This is achieved by the platform "gliding" over the soil, thus ensuring a cut at a minimum height. This effect is not achieved with conventional grain headers.

Brief technical characteristics of the John Deere 635F GydraFlex header:
Year of manufacture 2008,
Full-finger auger - FULL FINGER,
Composite fingers along the entire length of the auger,
Floating washer (instead of the MCS, the so-called Schumacher manufactured by John Deere),
A bar behind the platformr to prevent stones from getting under the auger,
The working width is 10.67 meters,
Sliding plates on the bottom,
Automatic feeding of the reel back and forth and up and down by hydraulic cylinders,
Plastic dividers.
Mounting for John Deere 50, 60, 70 series STS combine harvesters. It is possible to adapt this reaper to the Claas Lexion combine by replacing the shaft, sprocket, pulley, etc.
The plastic plates are in good condition.
The John Deere 635 F GydraFlex header will provide the necessary maneuverability to copy the relief of the mowed uneven field surface, while reducing losses during harvesting soybeans and other fallen and stunted legumes. This effect is achieved by adjusting the pressure from the cab (hydraulically) on the soil.
This header can also be used in the rigid cutterbar position for threshing normal (medium-sized) crops by closing the appropriate mechanical brackets.

Thanks to the composite fingers located along the entire width of the auger (auger diameter is 66 cm) and a 12.7 cm high coil, the auger of the 600 series reliably copes with the supply of mowed crops to the inclined chamber of the combine harvester.

The reaper can be combined with all models of John Deere combine harvesters, and after preliminary adaptation by replacing the pulley and sprocket on the reaper and adjusting the hydraulics on the combine, it can work with Claas Mega and Lexion, New Holland, Case, Massey Ferguson combines.
The John Deere Hydroflex can be combined with John Deere 60 series and newer combines without additional adaptation. With the installation of a smaller sprocket and a smaller pulley, as well as additional hydraulic settings, it can easily be mounted on Lexion and Massey Ferguson combines. It also works with Case and New Holland.

John Deere 635 F GydraFlex (John Deere 635 GydraFlex), working width 10.7 meters, composite fingers throughout the Full Finger auger, full-finger auger, the so-called "Schumacher" manufactured by John Deere Co. (original), planetary mechanism instead of the gearbox (more durable, reliable than the gearbox).